Search results

any one have a copy of a schematic for a 94 explorer i have installed a 94 and im having problems with codes 56 66 mass air need to trace wiring. thanks steve

my 88b2 has a 4.0 motor in it i installed a couple of years ago. i read my computer and i have quite a few code errors. ive looked them up but dont understand what they mean,im looking for more info on what they mean and what part is involved. the codes are #27,29.32,56,66,93. for instance code...

i have a 1988 bronco II with dana 35 front end with jeep limited slip ,0 lift love it! my question is what year front shock should i use 1988 or 1994 when i shop there different, im guessin at 1990 to 94 thats the years for the dana 35. your opinion appreciated. thanks steve

i have a 1993 explorer 8.8 rear end for my broncoII i want to change the ring@pinion to 4.10 ratio.will a 1998 explorer 8.8 ring and pinion fit in a 1993 rear end looking at one on ebay. thanks steve

my bronco II has a 4.0 i put in a while back . im having a problem with the fan hitting the shroud and breaking the fan blades when im putting high torgue like a steep hill 4 wheeling. im using the 4.0 shroud and radiator. i used the stock 2.9 motor mounts! i obviously need to change these...

i have 86 b2 and i cant figure what this is or does ,when i took it apart it looks like it should have a filter in it.the reason im asking is i drove it on a 300 mile trip ran great, but on the way home it started acting like it was running out of gas. as long as i kept it below 6o mph it...

will a 84 bronco II c5 from a 2.8 bolt to a 2.9 0r 4.0 i have one and ive heard there a lot stronger than a4ld's your opinion would be appreciated. thanks

i have a dana 35 in my bronco II with jeep limited slip with 4:10 ratio,ive decided to put a 8.8" rear end out of a 93 explorer ratio 3:73 ,i also bought a front punkin dana 35 with 3:73.trans is md5r. i want the higher gear hoping to get better mileage have plenty of power and dont do...

i have 88 bronco II with 7.5 limited slip differential i need to replace the clutch packs in differential! can someone direct to the best place to buy. also what gear oil is best? thanks

i have a 1991 explorer the radius arm bushings are toast,when i hit the brakes the front end pops, ive looked through my books to find out the easiest way to replace looks the easiest is removing the crossover there held in. any ideas would be appreciated thanks

getting ready to replace carpet ,and also tire cover wheres the best place to to buy. also thinking about vinyl rather than carpet any opinions would be appreciated so many sites dont want to get ripped of. thanks steve

i bought a m50d 5 speed trans im replacing my al4d for manual i cant figure how to disconnect the hyd slave line at trans ive taken the white plastic sleeve of but cant get it to release. i dont like to force things and possibly break it any help would be appreciated thanks

i looked it up says (orm) EGR feed back is low evr or pfe, can anyone tell in english what this is,or what i should check? thanks

ive completed my change over from a1994 4.0 to my 1988 broncoII. wiring is about 90% complete the temp guage wiring on the 1988 ive found (red/white) on the explorer wiring loom there is a red white coming out of the wiring loom plug passenger side the loom that comes over the top of the motor...

1991 4wd 2dr explorer ive been through hanes and chilton looking for a schematic to trouble shoot my transfer case, will not engage last week went four whelling when i tryed to disenguage had to finally stop and play with control button to disenguage. now when i hit the 4 wheel button it doesnt...

i recently replaced heads on my 1990 2dr exp ,both heads had small cracks. bought two used heads maged and had valves ground put the heads back on runs great. my problem is now when it gets warm the lifters are noisy. 2.9s were adjustable rockers on 4.0 are not so i cant adjust valves. my oil...

i have a 1991 ford explorer with a a4ld, i want to do a total fluid change. the trans shop wants $150.00 is there anyway i can perform this at home. thanks.

i have a 1986 ranger with a mitsubishi 5 speed 4wd its on its last leg. my question is will a 1984 toyo koyo 4wd work. i know the bell house is different (slave cyl change) but i also have 2wd drive toyo koyo with the newer bell housing. the lengths are real close about 27" long will this work...

i have a 1988 bc im getting ready to put my 4.0 in ,i have the wiring loom from a 1994 along with computer and all motor neccesarys. i have 2 a4ld from a 1988 and a 1991 will these work they both are dual cylonoid although im told the 1991 is stronger due to upgrades in trans. also what year...