Search results

started out i was driving to work, suddenly the car shuts off and smokes come out of the hood. the black with orange stripe wire fusible link had fried and caught fire. so i began to unravel the loom and traced to the fuse panel and the headlight switch. i figured it shorted because it got a...

not sure why but i just had all my leaks fixed and the motor cleaned so if it did leak oil again we would see it. it was rebuilt last year. and now the oil light flickers at idle speed but doesnt when i accelerate. im mostly concerned with the amount of oil being added every week. at least...

is there anything i should know. something to tell them, something they should look for. kinda nervous about spending 1400 smackers. but i want a good trans.

i need to know the computer voiltage to the knock sensor wires. im getting 2.5 volts. is that good or bad.

im getting the code 21. iirc its ect out of range. i replaced both sensors and reset the computer with a genesis scanner. wait a few days and the codes returns with other codes following it. 21, 25, 33, 74, 77 my fault, and none erase. 77 was my fault so its not an issue i just thought id...

would it be a good idea to let it sit in a cleaner to soften up the hard carbon build up on it. it is stuck closed. so that is why im asking. ill buy a new one if i have to spend the money. just looking for another way around spending if i dont have to

trying to figure it out. rebuilt 6000+ miles ago. new fuel pumps and filter. no codes that i know of. i believe the fuel pressure reg has been replaced. its the shinniest part on it. plus no fuel smell or strong taste. i dont believe the injectors are sticking o2 sensor has been replaced...

86 b2 2.9 auto either going up hill on a long drive through the mountains or four wheeling through some mountain trails. many new parts. fuel pumps and filter. new reman distributor and ecm. rebuilt 6000 miles ago. havnt replaced any sensors cept oil pressure sending switch. some oth er...

hey guys, i got a question about my oil pressure sensor. the other day the light my blinking, i know they stay solid when a problem is present. it only does this blinking thing when at idle, as soon as i hit the gas it stops. i have it unhooked and the light isnt on. now should the light be...

86 bronco 2 auto. new rebuild just over 500 miles. new fuel pumps and filter. new distubitor cap and rotor question is, im thinking and feeling like it doesnt have a lot of top end power. i dont have a timing light but ive got it pretty close. it idles at 850 900 rpms. just feels gut...

fresh rebuild only 300+ miles and the seal starts to leak. thought is was the oil pan gasket towards the rear. i pulled the motor out and took off the oil pan. noticed the ream main seal was on backwards. flipped it and put on a new oil pan gasket. the rms is new btw. i dont understand after...

now that i have gotten the modulator back in. all new hoses. now it shifts between 2000-3000 rpms with a medium pedal id say 30% is this normal. or does it need some more adjusting and if it does how do you do it. i know there is a allen head for a screw like thingy on it. do you turn it to...

need help. my automatic trans doesnt seem to be taking off in first gear. feels like major slipping but i know its not taking off in first. trans fluid level is good and fresh oil. i dont know much about the truck or if it had any issues before i got. any help would be helpful. ill keep...

hey guys. im doing a rebuild on my b2 next month. and i was wondering about the break in period. i need to know the best methods to take. exp. how many miles drivin. what rpm range. how fast can i go to not hurt the engine. how many mph can i drive

ok so i know that it can be done. only because the valvetrain is adjustable. so my question is, is it worth it and is it reliable. how much power comes from taking away metal from the bottom of the lobe. it makes sense but at the same time it doesnt. the part that im having a hard time...

ok does the newer improved heads fit a 86 2.9 engine. i want to get the 89tm heads, but im not sure they will bolt on. any body know this answer. thanks

hey ya'll just wondering if it possible but can the 2.9 head be p&p. cuz im already going to put a larger cam in it so i dont want to stop there. any info would appreciated

hi every one. my names chris. this is my sec bronco2, first one crashed and burned. not my fault. so anyways, this one is a 07/86 with a 2.9 auto. poor bronco has a cracked head, i didnt see this till after i did a head gasket set on it. can these be welded and called good for a long...