Search results

Hey guys, so my CV drive shaft took a crap on me the other day. I had a spare used double cardan drive shaft with the flanges on it. I ended up finally getting it on (had to let the rear end hang as low as possible and loosen the trans mount bolts to pry it forward) but anyways, I got it on...

Hey guys, I'm having an issue and hopefully it's something someone else has had so it will be an easy diagnosis. When I'm at low rpm (below 2000) every so often the engine hiccups and the tach will just drop like it's lost it's signal all of a sudden. It usually snaps right back up a second...

Hey guys, not sure if this is allowed but here goes. I may need to sell my B2 soon as I am moving and need some spare cash etc...What do you think is a fair market price for what I have? 1989 B2 4wd Approx 20k on full motor rebuild (2.9L) M5OD Trans Swap (all new bushings/metal seals) 10"...

Hey guys, I have an 89 B2.....I am doing the rear brake shoes and in all the pics I've looked at as well as the Haynes manual there are two little prongs that come off the wheel cylinder and contact the shoes. On mine there are just two pistons with no little prong things....is something wrong...

Hey Guys, I've got a 1350 Manual TC. There is a nipple with a hose connected which then splits at a T into two hoses. I'm assuming these are vent hoses, do they attach to anything or should I just wire tie them up? My B2 was originally 2wd so I'm not sure where these are supposed to go as I...

Hey guys, I've got a lot of help here in the past and appreciate it greatly. I have another question I'm hoping to get cleared up. Here goes: I've got an M50D with a 1350 manual TC. The rear driveshaft fits fine but the front driveshaft is too short, I would say it's about 3 inches too short...

Ok, this is a bit of an oddball questions but here goes.... I just converted my 2wd B2 to 4wd AND installed a M5OD, to convert to 4wd I used a transfer case from a TK transmission and bolted it up to the MDO5. The bracket for the transfer case "shifter" that was attached to the MDO5 looks as...

Hey guys, just a quick question. I'm ordering a clutch tomm and I wanted to make sure I'm getting the right thing. I've got an 89 BII with an M5OD, I want to order a clutch from a 90-92 Explorer/Ranger 4.0L correct? I just wasn't 100% positive about the year I'm supposed to order.

Hey guys, I'm converting my 2wd to 4wd and my current exhaust is directly in the way of the front driveshaft. It looks as though it is an aftermarket replacement as it uses slip fittings right after each collector. My question is....are the 2wd and 4wd exhausts different or maybe someone in the...

Hey guys, I was wondering what it would take for me to be able to fit some 33x12.5x15 tires on my 89 B2. I already have 15" wheels (stock), would those work with that wide of a tire? Will I have clearance issues? Thanks guys!

Hey guys, I'm piecing together all the stuff I need to swap my FM146 out for an M5OD and ALSO do the 2wd -> 4wd swap. For the transmission I've got: Transmission Clutch Flywheel Shifter Assembly Block Plate 4.0L Manual Starter 4Ga wire for starter etc... For the 2wd -> 4wd conversion I have...

Hey guys, my other thread was getting a little off topic (due to me asking lots of questions) so I figured I would start my second search for data here. I'm interested in swapping in the parts to do the 2wd -> 4wd conversion on my 89 B2. Could you guys let me know which vehicle the 4wd items...

Hey guys, I have a 1989 Bronco ii 2wd. On thanksgiving day the transmission blew out on me in the middle of nowhere leaving me on the side of the road in the rain for 7 hours. Anyways, long story short, I had a tranny shop check it out and they said it seems that 5th gear welded itself to the...