Not Another CTOR Build

[PaleBlue90]

are those parts painted purple?

 

[smallfarm123@aol.com]

pretty cool cant wait to see wat it looks like when your done

 

[CheapThrillB2]

the third is, the axle housing will be black

 

[CheapThrillB2]

little spacers to center the rotors to the studs to elimante any play in the rotor at axleshaft mating

Purple and done :teehee:

painting the center section before installing the third leaving the outsides primer till the spring perches, shock mounts, and brake calipers are welded on

 

[danger88ranger]

painting the center section before installing the third leaving the outsides primer till the spring perches, shock mounts, and brake calipers are welded on

I assume you used weldable primer so you don't have to grind the primer down again?

 

[CheapThrillB2]

nope, i'll grind down the primer when it comes time, not a big deal

 

[CheapThrillB2]

i had to grind the caliper brackets i bought to fit on the axle, the pads and rotors didn't line-up as in didn't sit with full contact surface of the pads against the rotors. all better now, the brackets are welded to the axle.

the grinder kinda got away from me on the first one lol

 

[CheapThrillB2]

 

[badblue]

What rotor /caliper are you using and what you planing on running for rim size?

 

[CheapThrillB2]

front chevy 4x4 1/2 ton 74 calipers

95 4wd 1500 dodge front rotors

15x8 38x12.50

 

[badblue]

thanks had cadie one and had rubbing on my 15 mikiestomson wheels

 

[CheapThrillB2]

where they aluminum, the rims?

 

[CheapThrillB2]

Just recieved my tracking number from Ballistic Fabrication for my DIY BeadLocks....Fedex puts it with delivery of Feb 2nd though

I hope to get a ton of work done this weekend.....i FINALLY have a Saturday off from work.

 

[CheapThrillB2]

I cannot get the D44 gears installed with a good pattern...this thing is kicking my ass. I have gone through all kinds of shims, moving them around, taking the pinion in/out and replacing shims..........I am starting to wonder if the i do not have a housing problem.....

I have another D44 housing at the house i think, i might just grab that and start over....

 

[CopyKat]

I hope to get a ton of work done this weekend.....i FINALLY have a Saturday off from work.

Looks like you've been doing this at work as it is. Not everyone can rebuild a 9" in 2 days and work at the same time. Works has been slow then??

So your working on it this weekend? So I expect it to be done and first test drive on Monday!:icon_rofl::icon_hornsup:

 

[CheapThrillB2]

yeah works slow in the shop, i am averaging half my normal flat rate hours for a normal week, so i gotta do something with my time. Not like i'm getting paid while i am at work when not working on a car.

I am hoping to have the rear susp done, coil buckets made, and the engine trans and tcase installed and possibly getting the body on the frame this weekend.

 

[Mechanickid]

:icon_hornsup:

 

[Bray D]

I cannot get the D44 gears installed with a good pattern...this thing is kicking my ass. I have gone through all kinds of shims, moving them around, taking the pinion in/out and replacing shims..........I am starting to wonder if the i do not have a housing problem.....

I have another D44 housing at the house i think, i might just grab that and start over....

Is it with the USA Standard gearset or the Yukons?

 

[CheapThrillB2]

Is it with the USA Standard gearset or the Yukons?

i jsut can't find the right combo of shim locations to get it right, just frushstrating

 

[Bray D]

I see. Post up pics