Not Another CTOR Build

[CheapThrillB2]

Looks good. Will your RA interfere with your tranny crossmember at full bump?

at a glance i would of thought so, but i don't think it will.....if it does i have a 84 crossmember

 

[Bray D]

I see. Didn't know if you checked during mockup. Your RA location is close to where mine will be, and I've got an idea what to do with the crossmember if it does interfere. Hopefully it won't though.

 

[CheapThrillB2]

holshotracer basically has the same set-up and hes been rnning is for almost a year and he hasn't hit his yet.

 

[Mechanickid]

not to be nosy but how much do you think you have in it?

 

[CheapThrillB2]

not much as compared to others

Right now with its current set-up....(i have bartered and traded alot to get what i have)

Axles about $1K (everything brakes/gears/etc)
Tires (traded a truck and other stuff for)
Beadlocks $200
Cab $100
engine/trans $75
Seats $300
5 points $50
Winch $280
coils $150
Shocks $140

$2259?

Satisfaction of building from a bare frame basically and doing 90% or better yourself......PRICELESS

 

[Mechanickid]

Not Bad! I love budget built rigs. Plus its all built not bought

 

[Big Red Ranger]

dude you have built so many amazing rigs nice job

 

[Bray D]

holshotracer basically has the same set-up and hes been rnning is for almost a year and he hasn't hit his yet.

Good to hear. So you said if it does you have an 84 crossmember to swap in? Whats the difference? Do you have a pic? Was it only offered in 84 or is there a range of years?

 

[CheapThrillB2]

i have never seen the crossmember on on anything newer then 85. Always found them on B2's with 2.8Ls

I'll try and dig up a pic

 

[CheapThrillB2]

i got my steering drilled and tapped, slow at work with little to nothing to do.

I usually make the jam nuts but i said to hell with it and ordered them from RuffStuff for $20 for all4 shipped.

 

[Mechanickid]

How many trucks has that 4.0L been in? lol

 

[CheapThrillB2]

2 frames

came from 91 explorer and it was installed in my B2 build (this is the same frame as my B2 for the truggy)

 

[holshotracer]

I see. Didn't know if you checked during mockup. Your RA location is close to where mine will be, and I've got an idea what to do with the crossmember if it does interfere. Hopefully it won't though.

i haven't even hit mine once. you would think that it would hit but at full stuff i have about an inch of clearnce.

 

[CheapThrillB2]

Good to hear. So you said if it does you have an 84 crossmember to swap in? Whats the difference? Do you have a pic? Was it only offered in 84 or is there a range of years?

heres the 84-85 next to the 86

 

[Bray D]

Oh cool. Thanks for the pic. So it goes over the exhaust rather than under it. That'd be nice.

 

[CheapThrillB2]

yes, but it does not fit well over the convertors.....or a doubler do to the driveshaft location.

 

[CheapThrillB2]

Steering installed, Front shocks installed, Started on the front bumper, and played a little and flexed it out a little with the chain fall.

Front springs def need to get broken in though. Still not happy with the overall ride height....but i will have to most likely wait till after my trip south to change that.

 

[Crazythingsido2]

looks sick

 

[CheapThrillB2]

okay basically this is just the back of the cage veiw only (or "c" pillar)
each color represents a peice of pipe.

side veiw

red is exsisting c pillar

 

[CheapThrillB2]

i'm on dinner break lol

going back out in a bit to start on the rock sliders.